Chimney accessories

Combine these pieces to make the ideal support for the cathedral ceiling chimney.

Use this complete fireplace starter kit for your wood stove.

Use this additional support when the chimney height exceeds the height that the initial support can hold.

Facilitate the transition from SuperVent chimney to a simple or double wall stove pipe with twist-lock connection with this adaptor.

Make an installation for cathedral ceiling for this chimney support.

Install this round ceiling trim to the junction of the stove pipe and the masonry chimney for a neat finish.

Use this universal roof guy kit for a better support in case your chimney elevates 5 ft or more above the roof.

Chooose this increaser to add to the chimney.

This snow splitter is designed to deflect snow and ice. Panels are easily assembled and prevent unnecessary strain or damages to the chimney. The splitter is made from heavy gauge galvanized steel and mounts directly on the roof above the chimney.

This galvanized steel storm collar maintains a weather tight seal between the vent and the roof flashing. Silicone must be applied (not included). Preserves fuel clearance.

This ceiling support is used for the vent system from below the ceiling joist. It maintains a 1″ clearance to combustibles.

This increaser adapter for pellet vent stoves is used to increase the size of the pipe to the chimney. It attaches to 3″ collars and connects to 4″ vent pipes.

This galvanized adjustable wall band stabilizes and supports pellet stove pipes against an outside wall. It is adjustable from 1″ to 3″ and maintains clearance to combustibles.

This adjustable pellet flashing is used for a waterproof installation through pitched roofs from 0/12 to 6/12 and 6/12 to 12/12. It maintains fuel clearance.

This pellet stove pipe increaser is used to connect a 3″ pellet pipe to a 4″ pellet pipe.

This appliance adapter is used to connect a pellet pipe to the outlet of a pellet stove. The female end adapts to the stove outlet with a leakproof connection.

This 90º elbow for pellet stove is used to orient a pipe between vertical and horizontal orientation. Tight fit reducing leakage.

This 45º elbow for pellet stove is used to orient a pipe between vertical and horizontal orientation. Tight fit reducing leakage.

This corrugated elbow is used to connect two lengths of drain pipe.

Regulate the waste gases of your home thanks to this plumbing roof vent.

Install this roof flashing for high-rise roof.

Optimize the proper functionning of your plumbing roof vent with this replacement cap.

Maintain the water-tightness of your roof by installing this high-density thermoplastic flashing.

The DELTA-FLASH is an angled flashing for smooth edge finishing, cut-outs in windows and doors and vertical edges.

FlashSealR Foam Flashing helps provide effective protection against air infiltration and water penetration.

Get a perfectly filtered ventilation with this flashing designed for roofing with a pitch up to 40° (10/12).

Get a perfectly filtered ventilation with this flexible flashing designed for roofing with a pitch up to 45° (8/12).

Used to connect two lengths of flue pipe together.

This T-adapter is used for pellet appliances. It is used as a starting pipe on the exhaust outlet of the appliance. A top silicone gasket connects in seconds to ensure gasket integrity.

Designed for inclined roofs, this vent offers 418 CFM airflow using 4 deflectors through 12 openings. Thanks to its adjustable flashing, it adapts to roof slopes from 1/12 to 15/12. Its 12" x 12" dimensions allow it to ventilate areas between 1,000 and 1,200 square feet. It is ideal for ensuring good air circulation in attics and preventing moisture buildup.

Aids in cleaning and inspection.

Used to connect two non-crimped ends of pipe together, crimped on both ends.

Used to connect two lengths of flue pipe together.

Used to increase flue pipe size, crimped on big end.

Install on wall where flue pipe connects to masonry chimney breech.

Used to connect two lengths of flue pipe together, adjustable from 0° to 90°.

Used to reduce flue pipe size, crimped on small end.

Used to reduce flue pipe size, crimped on small end.

Used to increase flue pipe size, crimped on big end.

Self-drilling screws made from Black Zinc.

Used to increase flue pipe size, crimped on big end.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.

Equip the top of your chimney of this galvanized rain cap with fireguard.